The DIY Homeowner's Guide: Installing in-wall and in-ceiling speakers.
Like many homeowners, you probably enjoy home theater, but you'd prefer not to have five speakers and a subwoofer on your living-room floor. Then consider in-wall speakers as a solution. The question is, can you install them yourself, or should you call a professional? The answer is, yes you can install in-walls yourself, with some planning, a few basic tools, and a little patience. Here's a step-by-step overview of the process of installing in-wall (or in-ceiling) speakers, as well as the parts and tools you'll need to complete the job like a pro. Assuming you have a few basic tools (a cordless drill, screwdrivers, tape measure, level, wire cutters, and a staple gun), the cost of this project, excluding the speakers, should be about $150 to $200 (for the fish tape, hand drywall saw, stud finder, and speaker switcher).
Step 1: Select Your Speakers With the exception of some high-end models, most in-walls are rectangular, between 10 and 18 inches tall, and designed to fit between wall studs, which are spaced 16 inches on center. Many speakers are round and suitable for in-wall or in-ceiling installation. Some in-wall speakers come with enclosures or back boxes, and some do not. In general, speakers with enclosures have more predictable bass performance because they are not dependent on the volume of the wall cavity, which varies among homes.
In-wall subwoofers are also available that fit neatly into a wall cavity. Most in-wall subwoofers are passive, meaning they are not powered and need a separate amplifier.
Step 2: Determine Speaker Placement and Locate Obstructions Behind the Walls Once you've found the best location for the speakers, check for any obstructions behind the wall, such as pipes or wires. The easiest way to do this is to drill a small 0.25-inch hole in the wall and insert a coat hanger bent at a
90-degree angle. Move the coat hanger around to feel for any obstructions. If you find any, it's easy to patch the small hole and find another location. Another method is to cut a larger hole and insert a small mirror to view the inside of the wall cavity for potential obstructions. It's important to locate the wall studs and install the speakers directly between them. You can locate the studs by tapping on the wall, but the best way is to use a stud finder, available for about $15 at a hardware store or home-improvement center. If you don't find any obstructions, and you've located the studs, it's almost time to cut the drywall.
Step 3: Cut the Holes for the Speakers > Helpful Tip: Use a shop vac, not a household vacuum cleaner, to clean up any drywall dust. The fine-grained drywall dust will ruin a household vacuum cleaner. I learned this lesson the hard way.
Step 4: Running the Speaker Wires To run wires through walls, also known as fishing, you'll need a tool called a fish tape, which electricians use to pull electrical wires through inaccessible areas. Fish tape is a length of stiff wire with a hook at the end. A long fish tape is wound around a reel, and a short fish tape (4 feet) is not. In some cases, you'll need both to complete the job. You can purchase a long 25-foot fish tape for about $20. If you are running the wires overhead through the attic, you may need to drill an access hole through the top plate(s) (one or more two-by-fours) of the wall and down into the wall. If you are working from beneath the floor, you may need to drill a hole in the bottom plate(s) up into the wall. If you're running wires laterally through the walls, you may need to cut small holes in the drywall to expose the studs and drill holes large enough for the wire. The drywall holes only need to be 1 inch high and wide enough to expose both sides of the stud. And you can easily patch them. If you decide to run wires behind the baseboards, remove them and cut a channel into the drywall with a utility knife, run the wires, and then replace the baseboards.
The recommended size or gauge of the wire you use depends on the distance from the amplifier or receiver to the speakers. Typically, 14- or 16-gauge wire works well for most installations up to 100 feet. Beyond that, use 10- or 12-gauge wire, which is larger in diameter and requires larger holes. Use good speaker wire for the best sound quality. It's a good idea to staple or secure the wire in place, whether you're running the wires through the attic or under the house. Be careful not to pierce the insulation around the wire while stapling. When working in the attic or under the house, be sure to wear gloves, a mask, and a cap to protect you from dust, fiberglass insulation, and other hazards. Note: If you are installing speakers in several rooms that are powered by one amp or receiver, it is important to install a switcher with an impedance-matching device. This is essentially a small box with several speaker connectors that ensures that the component will work with multiple speakers. An Internet search for impedance-matching speaker switchers found multiple models that will accept up to six pairs of speakers for under $100.
Step 5: Installing the Speakers Most in-wall speakers use four or six dog-leg clamps to secure the speaker to the wall, and some have a gasket that goes between the speaker frame and the wall to prevent vibrations and wall rattles. After inserting the speaker (and gasket, if applicable) into the cutout, tighten the screws on the front of the speakers to move the clamps into position and attach the speaker to the wall. Some speakers use a perimeter clamp, which uses the entire frame to clamp the speaker to the wall. Both types work well when properly installed. Some in-wall speakers are installed in two pieces. The frame is secured to the wall, and the speaker is then inserted into the frame. Consider installing some insulation (R-13) in the wall cavity behind the speakers to improve sound quality. The width of the insulation is usually pre-cut, so you only need to cut it to length and insert it in the opening behind the speakers.
Step 6: Connect Speaker Wires to Amplifier or Receiver and Test for Sound Turn on the amp or receiver to perform a sound check. Start at a low volume, in the case of a problem. Listen to each speaker, and use the balance control (stereo receiver) or speaker test tones (multichannel receiver) to make sure all channels are connected correctly. If you don't hear any sound from a speaker, shut off the receiver and check your connections. If the receiver turns on and then immediately shuts off, you probably have a wire connected incorrectly, bare wire touching metal, or a bad connection. Re-check the connections on each speaker and on the back of the receiver. > Helpful Tip: Speaker wires usually have marks or colors that identify positive and negative wires. If yours don't, use tape to mark them for easy identification.
Step 7: Optional, but Highly Recommended
Parts and Tools Required:
< Previous Post | Next Post >
|
|
